Change the SSID and wireless password tip

Product line: wireless  question category: wireless settings

 

1.Connect the router to your computer.

2.Login to the setup page of the router 192.168.0.1,click on Advanced settings.



3.Change the SSID



4.Change or set a wireless password.



 Now you can use your laptop to search the new SSID and enter the new password to connect to it.

Source   http://www.tenda.cn

Posted by News For Thai 11:39 PM 0 comments

Reset TP-LINK products with WPS/RESET button tip

Notice:

1.    If you reset the device, the device will return to factory defaults, you will lose all your settings. Do not perform a hard reset unless you have backed up your settings or you can do the configuration again.

2.    For these models, we could see WPS/RESET button on the rear panel/the Front Panel. To use WPS function, please push the button for less than 5 seconds, and then the WPS LED will flash; to reset the router, please push the button for at least 10 seconds.

There are two methods to reset to the Router's factory defaults:

Method 1 ：Hard reset/By pressing the RESET button

With the Router powered on, press and hold the WPS/RESET button (more than 10 seconds) until the SYS LED becomes quick-flash from slow-flash. Then release the button and wait the Router to reboot to its factory default settings.

Method 2 ：By Router's Web-based Utility (management page)

 

If you are on the management page, you could use the Factory Defaults function.

Please go to System Tools -> Factory Defaults” page, then click on the restore button and wait the Router to reboot to its factory default settings.

Note:

1. Make certain that the router is powered on before it restarts completely.

2. The default IP address is 192.168.1.1/192.168.0.1/192.168.0.254, and the default login username and password both are admin (all lower case).

3.  Ensure that the IP address of your computer is in the same subnet with the device. It means that your computer has an IP address 192.168.1.X /192.168.0.X(X is in range of 2~253), and the subnet mask is 255.255.255.0.

 Source   http://www.tp-link.us

Posted by News For Thai 11:31 PM 0 comments

upgrade tp-link mr3020 to the latest firmware trick

Frst plug an ethernet cable to pc and the tp-link mr3020. we use cable because it's more reliable than wireless. because upgrade firmware need stability. make sure pc power keep on while doing these action. because if the main process got interupted while updating firmware, it can brick the hardware it self. so using an ups is recommended.

change the ip of your lan. in windows 7 it can be done from start > control panel > network and internet > network and sharing center > adapter setting > local area network > properties > tcp ip v4 and change the ip from 192.168.1.1-X      (X= any number from 1-253)

now open your browser and point it to ip 192.168.0.254 you will be prompted by a box asking for login

the default user is admin and password admin


on left side bar u can find system tool > firmware upgrade. choose the firmware that we already download.
when asked are you sure bla bla bla... just press ok.. then wait until the router reboot. after that check the status bar.

voila... the router just upgraded well. you can see the version changed after we flash the new firmware. that's it

Source   http://tplinkmr3020.blogspot.com

Posted by News For Thai 12:27 AM 4 comments

Trick reset TP-LINK products to factory default settings (Wireless Router)

Suitable for: 300Mbps Wireless N Routers, 150Mbps Wireless N Routers, 54Mbps Wireless G Routers, N750 Wireless Dual Band Routers, N600 Wireless Dual Band Routers, N900 Wireless Dual Band Routers

Note: A hard reset will remove all your settings, and your device will be restored to factory default settings. Do not perform a hard reset unless you have backed up your settings or you can do the configuration again.

Directly press and hold the reset button on the rear panel with a pin for approximately 6 to 10 seconds when the device is running, then the device will be reset and reboot automatically.

Note:
1. Make sure the device is powered on before it reboots completely.

2. After the hard reset, the IP address of the device should be change to the default 192.168.1.1/192.168.0.1, and the default login username and password are both admin.

3. Ensure that the IP address of your computer is in the same IP range with the device. That means your computer should have an IP address like 192.168.1.X/192.168.0.X (X is in range of 2~253), and the subnet mask is 255.255.255.0, the default gateway should be 192.168.1.1/192.168.0.1, which is the IP address of the devi

Source   http://www.tp-link.com

Posted by News For Thai 12:19 AM 2 comments